Cisco 300-080 Exam Review Questions – Updated 2018

Customizable learning to have an estimation of time for each 300-080 question and to have a good understanding of the each Cisco 300-080 question’s pattern is possible by preparing with the Cisco 300-080 exam questions. PDF booklet provides you the most updated Cisco Certified Network Professional Collaboration 300-080 questions from the entire curriculum and the opportunity to practice those questions is available in the software so you have a complete package of Cisco Certified Network Professional Collaboration exam preparation for guaranteed success. Money back guarantee, MacAfee Secure payment, free demo, 90 days free updates for Cisco Certified Network Professional Collaboration 300-080 exam and much more just for you !

♥♥ 2018 NEW RECOMMEND 300-080 Exam Questions ♥♥

300-080 exam questions, 300-080 PDF dumps; 300-080 exam dumps:: https://www.dumpsschool.com/300-080-exam-dumps.html (157 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 300-080 Dumps Exam Questions and Answers:

Version: 10.0
Question: 21

In an MCU call with three Cisco TelePresence MX800 systems and a mobile phone calling in, the three TelePresence MX800 systems suddenly experience low audio levels, but the mobile phone audio levels are correct. What can you do to correct this issue?

A. Turn off the audio processors on the TelePresence MX800.
B. Use the mobile phone audio option on the TelePresence MX800 to adjust the mobile phone levels.
C. Mobile phone audio levels can vary, so you cannot correct the issue.
D. Turn on AGC on the MCU to adjust the audio levels.
E. Turn on ALG on the MCU to adjust the audio levels.
F. Turn on the Auto Adjust levels under “Settings > Audio” on the MCU.

Answer: D

Question: 22

When a user tries to initiate an Ad Hoc conference call from an IP phone, this message appears: No Conference Bridge Available. Which two actions resolve this issue? (Choose two.)

A. Make sure that the Join softkey is assigned to the phone.
B. Make sure that a Conference Bridge resource is registered to Cisco Unified Communications Manager.
C. Reset the phone, to re-register resources.
D. Make sure that a Conference Bridge Resource is assigned to the MRGL on the phone that initiates the conference call.

Answer: B, D

Question: 23

You configured a Cisco ISR G2 as a SIP gateway, but the gateway does not show that it is registered with Cisco Unified Communications Manager. What is causing this issue?

A. Cisco Unified Communications Manager does not support SIP gateways.
B. The gateway does not have the UC license installed.
C. The gateway does not have Cisco Unified Border Element session licensing.
D. Cisco Unified Communications Manager does not show a SIP gateway as registered if it is not properly configured.
E. Cisco Unified Communications Manager never shows a SIP gateway as registered even when it is properly configured.
F. The Cisco ISR G2 cannot be a SIP gateway.

Answer: E

Question: 24

Which issue would cause an MGCP gateway to fail to register with Cisco Unified Communications Manager?

A. missing the configuration command isdn bind-l3 ccm-manager under the ISDN interface
B. mismatched domain name on the MGCP gateway and Cisco Unified Communications Manager gateway configuration
C. misconfigured route group in Cisco Unified Communications Manager
D. incorrect MGCP IP address specified in the gateway configuration in Cisco Unified Communications Manager

Answer: B

Question: 25

Endpoints are configured for both H.323 and SIP using the same URI and Cisco VCS settings, but the endpoints register only as H.323 endpoints. What is causing this issue?

A. A firewall is blocking all traffic from the endpoints to the Cisco VCS.
B. The Cisco VCS has no SIP domains configured.
C. The Cisco VCS is blocking the endpoints because of duplicate ID entries.
D. The endpoints do not have the SIP option key installed.
E. SIP does not work, because SIP is used for Cisco Unified Communications Manager registration only.

Answer: B

Question: 26

You are trying to register an H.323-based Cisco TelePresence system to Cisco Unified Communications Manager and a Cisco DX70 system to the Cisco VCS Control. Why do neither of the units want to register?

A. The H.323-based system needs an E164 number to register to Cisco Unified Communications Manager, and the Cisco DX70 needs to have the MAC address configured first on the Cisco VCS Control.
B. The H.323-based system needs to register to the Cisco VCS Control with an E.164 number, and the Cisco DX70 needs the TFTP address to register on the Cisco Unified Communications Manager.
C. Both systems need to register to the Cisco VCS Control, but the H.323-based system needs to have the gatekeeper setting set to “Direct.”
D. Both systems need to register to the Cisco Unified Communications Manager, as the Cisco VCS Control is used only for firewall traversal.
E. You need Cisco TelePresence Management Suite to register Cisco TelePresence systems.
F. You need Cisco TelePresence Server to register Cisco TelePresence systems.

Answer: B

New Updated 300-080 Exam Questions 300-080 PDF dumps 300-080 practice exam dumps: https://www.dumpsschool.com/300-080-exam-dumps.html